Call Toll-Free: 1-855-FINORIC
Houston + Midland + Pleasanton, Texas, USA
Also Oklahoma, OK and Williston, USA.
Search our website here:
Sodium Formaldehyde Bisulfite, Sodium Hydroxymethanesulfonate SDS MSDS Sheet, Manufacturers' Represantative
FInOrIC, etymologically derived from our business line of Fine Inorganic, Organic and Industrial Chemicals, is the internationally preferred source for Chemicals. With customers in 55 countries across 5 continents, we source and sell most chemicals. Backed by company owned & operated full-fledged chemical manufacturing facilities in Midland & Houston, Texas with associated manufacturing sites in India, Dubai and China we are a truly multi-national chemical manufacturer and distributor.
Most of our or our partner facilities are either FDA-cGMP certified, ISO-9001:2008 certified, Halal and/or Kosher certified, REACH pre-registered ISO-22000:2005 HACCP.
Sodium Formaldehyde Bisulfite, Sodium Hydroxymethanesulfonate Manufacturers Specifications and write-up
Sodium Formaldehyde Bisulfite
CAS No.870-72-4, Molecular Weight 134.1, Molecular Formula CH2(OH)SO3Na
Sodium Formaldehyde Bisulfite SDS, Sodium Hydroxymethanesulfonate Safety Data Sheet
MSDS Sheet, Material Safety Data Sheet
Section 1 - Chemical Product Identification
Product Name & Synonym: Formaldehyde Sodium Bisulfite. Formaldehyde sodium bisulfite; Formbis; Monosodium hydroxymethanesulfonate; Sodium hydroxymethanesulfonate; Sodium hydroxymethylsulfonate.
CAS #: 870-72-4
EINECS EC Number: 212-800-9
Molecular Formula: CH3NaO4S
Molecular Weight: 134.08
Recommended uses and uses advised against (if any): Industrial Manufacturing.
Company: Finoric LLC
Address: 8115 Loop 540, Beasley, Texas, 77417 USA
In case of emergency contact:
Section 2 - Hazards Identification
GHS, Globally Harmonized System Classification in accordance with 29 CFR 1910
Classification according to Regulation (EC) No 1272/2008
Not a hazardous substance or mixture according to Regulation (EC) No. 1272/2008.
This substance is not classified as dangerous according to Directive 67/548/EEC.
Labeling according GHS USA & Regulation (EC) No 1272/2008
GHS Label Elements
Signal Word: None
Hazards not otherwise classified (HNOC) or not covered by GHS:
May cause mild eye irritation.
May causes mild skin irritation.
P261: Avoid breathing dust/fume/gas/mist/vapors/spray.
P262: Do not get in eyes, on skin, or on clothing.
P281: Use personal protective equipment as required.
P302+P352 - IF ON SKIN: Wash with plenty of soap and water.
P303+P361+P353 - IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower.
P304 + P340 - IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.
P305 + P351 + P338 - IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P337+313: If eye irritation persists get medical advice/attention.
Section 3 - Composition, Information on Ingredients
Chemical Name: Formaldehyde Sodium Bisulfite or Sodium Formaldehyde Bisulfite or Sodium Hydroxymethanesulfonate.
CAS #: 870-72-4
EINECS EC Number: 212-800-9
Section 4 - First Aid Measures
Eyes: Check for and remove any contact lenses. In case of contact, immediately flush eyes with plenty of water for at least 15 minutes. Cold water may be used. Get medical attention if irritation occurs.
Skin: Wash with soap and water. Cover the irritated skin with an emollient. Get medical attention if irritation develops. Cold water may be used.
Ingestion: Do not induce vomiting. Get medical aid if irritation or symptoms occur.
Inhalation: Remove from exposure and move to fresh air immediately. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medical aid if cough or other symptoms appear.
Notes to Physician: Treat symptomatically and supportively.
Section 5 - Fire Fighting Measures
General Information: As in any fire, wear a self-contained breathing apparatus in pressure-demand, MSHA/NIOSH (approved or equivalent), and full protective gear.
Extinguishing Media: Use water spray, dry chemical, carbon dioxide, or chemical foam.
Flash Point: 184 deg C ( 363.20 deg F)
Auto ignition Temperature: 500 deg C ( 932.00 deg F)
Section 6 - Accidental Release Measures
Personal precautions, protective equipment, environmental precautions and emergency procedures: Avoid breathing dust/fumes/gas/mist/vapors/spray. Use individual protective equipment (waterproof boots, suitable protective clothing, safety glasses, etc.). Restrict unprotected personnel from the area. Prevent any contact with hot surfaces. Do not approach facing the wind. Do not touch the spilled material. Keep away from drains, surface and groundwater and soil.
Methods and materials used for containment Cleanup procedures and Storage:
Small Spill: Use appropriate tools to put the spilled solid in a convenient waste disposal container. Finish cleaning by spreading water on the contaminated surface and dispose of according law.
Large Spill: Contain spilled material. Use a shovel to put the material into a convenient waste disposal container. Finish cleaning by spreading water on the contaminated surface and dispose of according law.
Section 7 - Handling and Storage
Precautions for safe handling: Apply according to good manufacturing and industrial hygiene practices with proper ventilation. Wash thoroughly after handling. Do not drink, eat, or smoke while handling. Avoid contact with skin, eyes, and clothing. Use with adequate ventilation. Minimize dust generation and accumulation. Avoid breathing dust/fumes/gas/mist/vapors/spray. Avoid contact with eyes, skin, and clothing. Keep container tightly closed. Avoid ingestion and inhalation. Use individual protective equipment (waterproof boots, suitable protective clothing, safety glasses, etc.). Prevent any contact with hot surfaces. Containers of this material may be hazardous when empty since they retain product residues.
Conditions for safe storage, including any incompatibilities: Store in cool, dry and ventilated area away from heat sources and protected from sunlight in tightly closed original container. Keep air contact to a minimum. Store protected from heat, sparks and ignition sources and incompatible materials. Avoid contact with skin and eyes. Avoid inhalation of dust/mist/vapor. Do not store with incompatible materials like strong oxidizing agents.
Section 8 - Exposure Controls, Personal Protection
Engineering Controls: Facilities storing or utilizing this material should be equipped with an eyewash facility and a safety shower. Use adequate ventilation to keep airborne concentrations low.
Exposure Limits: Formaldehyde Sodium Bisulfite or Sodium Hydroxymethane Sulfonate or Sodium Formaldehyde Bisulfite is not listed by ACGIH, NIOSH, OSHA - Final PELs
Personal Protective Equipment
Eyes: Wear appropriate protective eyeglasses or chemical safety goggles as described by OSHA's eye and face protection regulations in 29 CFR 1910.133 or European Standard EN166.
Skin: Wear appropriate protective gloves to prevent skin exposure.
Clothing: Wear appropriate protective clothing to prevent skin exposure.
Respirators: A respiratory protection program that meets OSHA's 29 CFR 1910.134 and ANSI Z88.2 requirements or European Standard EN 149 must be followed whenever workplace conditions warrant respirator use.
Section 9 - Physical and Chemical Properties
Physical State: Sodium Formaldehyde Bisulfite or Sodium Hydroxymethane Sulfonate is solid.
Odor: None reported.
Odor threshold: Not available.
pH: 7 - 8 (100g/L aq sol)
Relative density: Not available.
Freezing/Melting Point: 200 deg C (decomposes)
Initial boiling point and boiling range: Not available.
Flash point: Not available.
Auto-ignition temperature: Not available.
Decomposition Temperature: 200 deg C
Upper/lower flammability or explosive limits: Not available.
Vapor pressure: Not available.
Vapor density: Not available.
Evaporation rate: Not available.
Flammability (solid, gas): Not available.
Partition coefficient: n-octanol/water: Not available.
Solubility: 800 g/L (20C)
Viscosity: Not available.
Molecular Formula: CH3NaO4S
Molecular Weight: 134.08
Section 10 - Stability and Reactivity
Chemical Stability: Hygroscopic; absorbs moisture or water from the air.
Conditions to Avoid: Incompatible materials, dust generation, exposure to moist air or water.
Incompatibilities with Other Materials: Strong oxidizing agents.
Hazardous Decomposition Products: Carbon monoxide, oxides of sulfur, carbon dioxide.
Hazardous Polymerization: Has not been reported.
Section 11 - Toxicological Information
Oral, rat: LD50 = 3200
Carcinogenicity: CAS# 870-72-4: Not listed by ACGIH, IARC, NTP, or CA Prop 65.
Mutagenic Effects: Not available.
Teratogenic Effects: Not available.
Developmental Toxicity: Not available.
Reproductive Effects: No information available.
Section 12 - Ecological Information
Ecotoxicity: No data available. No information available.
Environmental: No information available.
Section 13 - Disposal Considerations
Chemical waste generators must determine whether a discarded chemical is classified as a hazardous waste. US EPA guidelines for the classification determination are listed in 40 CFR Parts 261.3.
RCRA P-Series: None listed.
RCRA U-Series: None listed.
Section 14 - Transport Information
DOT & ADR/IRD: Not regulated.
IMDG: Not regulated.
IATA: Not regulated.
Section 15 - Regulatory Information
SARA Section 302 Extremely Hazardous Substances: None of the chemicals in this product have a TPQ.
Section 313: No chemicals are reportable under Section 313.
California Prop 65: California No Significant Risk Level: None of the chemicals in this product are listed.
Section 16 - Additional Information
Prepared by AJK on 5 July 2020Disclaimer:
The information and recommendations set forth herein are presented in good faith and believed correct as of the date the SDS was created. It is compiled from various sources and it is not necessarily all inclusive nor fully adequate in every circumstance. In addition, these suggestions should not be confused with nor followed in violation of applicable laws, regulations, rules, or insurance requirements applicable. This SDS is intended only as a guide to the appropriate precautionary handling of the material by a professionally trained person using this product. Individuals receiving the information must exercise their independent judgment in determining its appropriateness for a particular purpose. This shall not constitute a guarantee for any specific product features and shall not establish a legally valid contractual relationship.
Sodium Hydroxymethanesulfonate Manufacturers;
Sodium Formaldehyde Bisulfite Manufacturers:
Beasley Houston Pleasanton Midland, Texas, USA.
Also Oklahoma, OK and Williston, ND USA
Tel: 1-855-346-6742 (1-855-FINORIC)
We offer chemicals for industrial, laboratory and research use only. We are not drug dispensers or pharmacist. Our suppliers offer pharmaceutical grade products, manufactured under proper control for use in industries only.
Most products offered from our Houston TX, Midland TX, Pleasanton TX and Oklahoma, OK and Williston, ND area warehouse
We are looking for Technical Sales Representatives or Business Associates in New York, Williston North Dakota, Mansfield Pennsylvania, Zanesville, Ohio and Los Angeles Area, USA.
Inorganic Chemicals Aluminum Chloride Ammonium Chloride Ammonium Persulfate Barium Chloride Calcium D Saccharate Glucarate Calcium Hydroxide Calcium Sulfate Chromic Chloride Cupric or Copper Chloride Magnesium Butyrate Magnesium Chloride Anhydrous Magnesium Chloride Hexahydrate Magnesium Sulfate Manganese Chloride Manganese Sulfate Potassium Chloride Sodium Acetate Anhydrous Sodium Acetate Trihydrate Sodium Butyrate Sodium Diacetate Sodium Nitrate, Sodium Nitrite Sodium Thiosulfate Pentahydrate Sodium Thiosulfate Anhydrous Zinc Ammonium Chloride Zinc Chloride Zinc Sulfate Chemical Toll Manufacturers
Sodium Hydroxymethanesulfonate, Sodium Formaldehyde Bisulfite Suppliers, Manufacturers, Exporters, Importers
31 May, 2021