Call Toll-Free: 1-855-FINORIC
Houston + Midland + Pleasanton, Texas, USA
Also Oklahoma, OK and Williston, USA.
E-mail: info@finoric.comSearch our website here:
Water Recovery Surfactant, Flow Back Aid Supplier Manufacturers and Manufacturer's Representative for Fracturing
FInOrIC, etymologically derived from our business line of Fine Inorganic, Organic and Industrial Chemicals, is the internationally preferred source for Chemicals. With customers in 55 countries across 5 continents, we source and sell most chemicals. Backed by owned full fledged chemical manufacturing facilities in Midland & Houston Area Texas with associated manufacturing sites in India, Dubai and USA we are a truly multi-national chemical manufacturer & distributor. Fracturing and Fracking Industry can rely on our 24x7 - 365days service including week-end deliveries.
Most of our or our partner facilities are either FDA-cGMP certified, ISO-9001 certified, Halal and/or Kosher certified, REACH pre-registered ISO-22000 HACCP.
![]()
![]()
![]()
![]()
![]()
For SDS MSDS Sheet of Flow Back Aid, Water Recovery Surfactant Please Write to Us.
Flow Back Aid
Water Recovery Surfactant, Fracking or Fracturing Aid Suppliers
Spanish Tensioactivo de recuperación de agua, ayuda de retorno de flujo
Russian Восстановление воды, поверхностно-активное вещество, обратная помощь
Arabic جهاز استخلاص الماء المستنفد ، تدفق المساعدات
Surfactant S-112, Water Recovery Surfactant (FlowBack Aid)
Use:
S-112 is a proprietary non-ionic, non-flammable surfactant for use in acidizing and fracturing treatments. It is designed to improve recovery of the injected stimulation fluids and enhance ultimate recovery of hydrocarbons.
S-112 effectively lowers interfacial tension between stimulation fluids and hydrocarbons. It lowers the capillary pressure and allows for greater penetration in to the formation face, therefore promoting the recovery of stimulation fluids, connate fluids and hydrocarbons.
S-112 is compatible with all known fracturing fluid additives and has been successfully used in West Texas, South Texas, East Texas and Oklahoma for the past few years. S-112 is also pumped with acid spearheads to lower the breakdown pressures and minimize the possibilities of forming acid/oil emulsions where a separate non-emulsifier is not used.
Physical & Chemical Properties:
Appearance: Clear, Straw Yellow Liquid
Odor: Faint Organic
Density: 8.4 lbs/ga
Pour Point: Less than 20 deg F
Flash Point: Greater than 175 deg F
Typical Surface Tension: Less than 30 dynes/cm2
Typical Interfacial Tension: Less than 3 mN/m
Wetting Characteristic: Water WettingCompatibility: S-112 is compatible with most acidizing and fracturing treatment additives and friction reducers. However, a compatibility test is advised before use.
Environment: Not hazardous to the environment.
Typical Dosage: Typically used at 1 to 2 GPT with stimulation fluids
Temperature Limitations: Can be used across a wide temperature range, no lower temperature limitation on performance. Has been effectively used up to BHT of 350 F.
Packaging: 330 ga one way totes, 275 ga one way totes, 55 ga drums and bulk tank trucks
Availability: Pleasanton, TX; Beasley, TX and Midland, TX
DoT Classification: Not Regulated
Manufacturers:
Finoric LLC
Beasley Houston Pleasanton Midland, Texas, USA.
Also Oklahoma, OK and Williston, ND USATel: 1-855-346-6742 (1-855-FINORIC)
E-mail: info@finoric.comMost products offered from our Houston TX, Midland TX, Pleasanton TX and Oklahoma, OK and Williston, ND area warehouse
We are looking for Technical Sales Representatives or Business Associates in New York, Williston North Dakota, Mansfield Pennsylvania, Zanesville, Ohio and Los Angeles Area, USA.
16 March, 2022